Please wait while the page loads...

Will the check engine light reset itself?

The check engine light on your 2013 Toyota Tacoma will commonly shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going persuasive, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Toyota Tacoma light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Coggin Toyota at the Avenues so the light and code can be double-checked and reset.

Check Engine Light Service 2013 Toyota Tacoma

What do you do when you’re driving along in your Toyota Tacoma and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Toyota owners, your heart sinks a microscopic because you have microscopic idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Toyota Tacoma checked as soon as feasible. Ignoring that warning could end up causing intense break to expensive engine components.

When your 2013 Toyota Tacoma's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t proper, a computer turns on your check engine light. This amber or yellow light is frequently labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an computerized audit tool that is used by our Toyota auto repair mechanics at Coggin Toyota at the Avenues. There are also a number of relatively inexpensive code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to hint the issue and repair it.

2013 Toyota Tacoma Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are a few modern causes including something as explicit as a loose gas cap. Alternative modern reasons for a Check Engine Light are damaged oxygen sensor, dirty mass airflow sensor, faulty head gasket, a malfunction with the fuel injection system, faulty emissions control part, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Toyota Certified Technicians and the certified service protocol to isolate the root problem and repair it as crucial to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Toyota issue was fixed.

Every 2013 Toyota Tacoma was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its troublesome systems. The sensors are continuously detecting conditions while sending data to the electrical control company. If the electrical control company detects that the data is out of factory specifications, the Check Engine Light flashes telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is incorrect nor what to do about it. That’s where we come in; Coggin Toyota at the Avenues provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Highly Qualified Service professional.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is frequently between $88 and $111. The apt news, Coggin Toyota at the Avenues offers complimentary multi-point inspections and free diagnostics, in most cases, to assist determine the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more discernible failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it apt to get the fantastic code reading and diagnosis.

What could cause the check engine light to come on in a 2013 Toyota Tacoma?

When your check engine light comes on, this could be as practical as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a compelling problem that could cause compelling damage to your engine and come with a big repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow generally means something fewer compelling but a flashing check engine light suggests that your vehicle’s engine is in compelling trouble and service is needed rapidly. If your check engine light is flashing in your 2013 Toyota Tacoma, we incredibly recommend not to drive the automobile and schedule Toyota service at this moment. Below is a list of the most daily reasons your check engine light can come on:

  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Toyota Tacoma’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is typically caused by neglected maintenance, which is why Coggin Toyota at the Avenues offers a complimentary multi-point inspection with every Toyota service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Toyota Tacoma will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause back-up problems from overheating.
  • The battery is low or dead. The battery in your 2013 Toyota Tacoma is every extraordinary. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did various decades ago, and they don't actually require maintenance. The value of a new one depends on the type of Toyota you drive, but check our current service coupons and specials.
  • New Spark Plugs or Plug Wires are decisive for your 2013 Toyota Tacoma. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or departed, you will experience poor performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, large to more expensive repairs.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Toyota Tacoma is what determines how much fuel is decisive to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to clear changes, like altitude. If your Toyota Tacoma is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • Your 2013 Toyota Tacoma has a vacuum leak. Every Toyota Tacoma has a vacuum system that performs a wide variety of functions. The vacuum system also helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dehydrated out and crack, especially if they’re exposed to important heat or extreme bleak.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less ready for use when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2013 Toyota Tacoma's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to learn the decent mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • One of the most routine and frequent cause is that your 2013 Toyota Tacoma gas cap is loose, damaged or missing. The gas cap for your 2013 Toyota Tacoma serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is departed or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on urgently after you put gas in your 2013 Toyota Tacoma, first thing you should check is to make convinced the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or back-up item can wreak havoc on your 2013 Toyota Tacoma if it’s not installed correctly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound routine, bring your Tacoma to Toyota and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might cost a scant bit more but could save you money from having to get poor function and damage caused by poor installation function corrected.

What Does the Check Engine Light Mean?

One of the most typically misunderstood lights or indicators in your 2013 Toyota Tacoma is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in various added ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your 2013 Toyota Tacoma. Some of these include shifting automatic transmissions controlling engine speed, ignition timing, and implementing stability control, just to name a lot. With that being said, the check engine light can mean a variety of extra things. It can be as obvious as your gas cap being loose or as relentless as engine knocking. If your check engine light is on in your 2013 Toyota Tacoma, contact Coggin Toyota at the Avenues. Contact Coggin Toyota at the Avenues today! Our Toyota service department can help you find out what code is turning your check engine light on or analyze why your check engine light is glaring.

2013 Toyota Tacoma Check Engine Light

A flashing light indicates that the problem is rigorous and if not taken care of immediately may result in towering damage to the vehicle. If the check engine light in your 2013 Toyota Tacoma starts flashing, that means that the problem needs abrupt attention and your Toyota should be brought in immediately. This blinking light usually indicates a draconian engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can quickly raise the temperature of the catalytic converter to a point where break is probable, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can exactly be the cause. A detrimental, popular or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our team of automotive experts at Coggin Toyota at the Avenues straightaway by calling 9043376618. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very fancy repair.

How many miles can you drive with the check engine light?

It could be anything from a destructive sensor to plug wires needing to be replaced. Since each check engine code has its own level of severity, it is difficult to predict how frequent miles you can drive with the warning light on. The safest bet is to decipher the code and then plan your strategy accordingly. If you check engine light is flashing, we recommend that you pull over and contact Coggin Toyota at the Avenues to help indicate if your vehicle is reliable to drive in or if we recommend a tow truck.

Is it safe to drive your 2013 Toyota Tacoma with the check engine light on?

If the check engine light is twinkling, this means that there is a serious issue and it is recommended to service your Toyota Tacoma urgently. This question is not very classic because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is normally indicated by a steady glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more dangerous problem. Call the experts at Coggin Toyota at the Avenues by dialing 9043376618 so you can describe the issues. Or decrease your speed and bring your 2013 Toyota to our certified mechanics as soon as potential.

2013 Toyota Tacoma Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that microscopic light on your vehicle’s dashboard rapidly illuminates, but in reality, it is not something that should cause you to shut down in fear good away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Tacoma. There are hundreds of chance codes that your check engine light can represent. While that sounds daunting, with a microscopic patience, tackling needed diagnostics will give you amazing knowledge about your vehicle and will also allow that Check Engine Light to do what it is surely supposed to do: be your guide. Unfortunately, distinct and amazing vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of functional OBD codes, there are also hundreds of functional reasons for the light, including:

  • Computer output circuit issues
  • O2 Sensor
  • Transmission issues
  • Emissions controls issues
  • Ignition system faults
  • Old Battery
  • Fuel and air metering systems problems
  • Bad Spark Plugs
  • Loose Gas Cap or Missing Gas Cap

This is why it is crucial for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a risky concern, you risk harmful your car added by not repairing the issue good away. When your check engine light comes on, you should get it checked out instantly by a certified Toyota technician. Call Coggin Toyota at the Avenues at 9043376618 now or schedule your check engine light service online today!